Product Quick Selection Wheel

CAMTEC - 120W DIN Rail Supply HSE01201 SERIES

Features
  • 120 Watts Power Supply
  • DIN Rail 35mm
  • Metal housing
  • Up to 91% efficiency
  • -20°C...+60°C full output power
  • Continuous short circuit protected
  • Overload & low voltage protected
  • Soft start & auto-recovery
  • EMI/EMS EN61000-6-2.3
  • EN55022 class B
  • PFC: EN61000-3-2 class A
  • Series & parallel operation
  • High reliability. Shock & vibration resistant

HSE01201  SERIES

Product Overview

CAMTEC - HSE01201 SERIES 

DIN Rail 120 Watts Power Supply 

Available Outputs:   12V,  24V,  36V,  48V,  60V,   72V,   110Vdc  

Description   The HSE power supply series realizes very high power efficiency in a space-saving housing. This design enables Green Power applications and allows free air convection. Latest generation electrical devices relate to the high reliability of all Camtec products. The Camtec philosophy is, to employ 125°C low ESR ultra long life capacitors where expedient to achieve a superior lifetime of our products. The used screw terminals allow easy to wire and smooth service.

Parallel und serial operation:   Camtec power supplies of the same model and the same output voltage can be either used parallel or in series. The assembling of external parts is usually not recommended. Make sure that the output voltage of each connected unit is ±1% equal. We recommend connecting the DC-outputs to a neutral point or a power bar. Follow the safety norms of dangerous dc-voltages. Most of the HSE power supplies allow selecting a parallel operation mode with a switcher B (not HSE01201 & HSE03201). The parallel operation select tilts the C/V-chart a little bit. In result the switching is softer. The power sharing between the units is more accurate. The HSE models can be used floating until 300Vdc (not HSE01201 & HSE03201)

UI-Chart, overload and temperature control characteristic   The HSE models base on a typical resonance forward converter. The devices provide an ideal vertically C/V-chart with no foldback. Thus the converter is ideal for complex loads and DC-drives. Consciously we resigned an excessive Powerboost that mostly occurs in less exact working control circuits. The advantage is, that the power supply delivers its energy always controlled and constant to the load. Even with a faulty operation of the power supply the loads never expose to high risk. The temperature control follows the C/V-chart. The power will be reduced over the voltage and the current remains constant (CC-mode). If the power supply really overheats the output voltage will be shot down. When the temperature recovers the unit automatically recovers and restarts into normal operation. As a standard the power good relay allows to control the power supply.

Specifications

GENERAL
Output Voltage See selection table
AC Input Voltage 85..132Vac / 184..265Vac
Frequency 47…63Hz
DC Input Voltage 110…375Vdc
AC Input Current 115Vac <2.2A 230Vac <1.1A

Factory Adjust.

Tolerance Uout

115Vac <2.2A 230Vac <1.1A

Load regulation

< ± 0.5% 10-100%, 100-10%

Switching Frequency

100KHz typical

Basic Load

0 A

Efficiency

91% typ.

Load Protection

1,2x Irated ,auto recovery

Voltage Protection

145% of Uout , auto recovery

Short Circuit Protection

Continuous

Temperature Control

Upon request

Hold Up Time

> 30ms 230Vac

Inrush Current

< 16A (230Vac)

Softstart

50ms typical
RELIABILITY

Air & Surface Leakage Paths

> 8mm

Input / Output Isolation

I/P-O/P:4KVac

I/P-G:2KVac

O/P-G:0.5KVac

Power Good Relay (insulated)*

<48Vdc/500mA (not 72V, 110V)

MTBF

EN61209: 600000h

MTTF EN61209.SN29500

149600h @ 40°C 24/7 85% Load
ENVIRONMENTAL

Cooling

Natural convection

Ambient Temperature

Natural convection

Storage Temperature

- 40°C…+85°C

Clima/Dirt/Hight/Humidity

3k3, Kl.2, 3000m NN, 90% Hum.
STANDARDS AND APPROVALS

EMI

EN55022 class B / EN61000-3-2

EMS

EN61000-6-2,3

Safety

EN60950-1, EN60204-1

Safety class 1(A)

VDE0805, VDE0100
MECHANICAL

Dimensions (HxWxD)

124x50x96mm

Weight

510g

Connectors (AC & DC)

Terminal plug AWG26...AWG12

Selection Table

MODEL HSE01201.12T HSE01201.24T HSE01201.36THSE01201.48T HSE01201.60THSE01201.72THSE01201.110T
Rated DC Voltage 12Vdc 24Vdc 36Vdc 48Vdc 60Vdc 72Vdc 110Vdc
Nominal Current 8.0A 5.0A 3.3A 2.5A 2.0A 1,7A 1,1A

Adjust Range

11,4 - 13,2V 22,5 - 28,5V 34,2 - 39,6V 45,6 - 52,8V 57 - 66V 68 - 86V 100 - 120V

Ripple

(230Vac/20MHz)

50mVpp 65mVpp 65mVpp 100mVpp 120mVpp 120mVpp 200mVpp

Notes:

Options for telecom & military use available upon request

Technical Illustration

Back to Top

Ask Your Question