Product Quick Selection Wheel

Chrome DC-UPS Module DRU-24V10ACZ- 24V 10A

Features
  • Suitable for 24V system up to 10A
  • Zero switch over time from loss of DC input to battery operation
  • Built-in diagnostic monitoring for DC OK
  • Discharge and Battery Fail by relay contacts
  • Full power over entire operating temperature range from -20°C to +60°C
  • LED indicators for DC OK
  • Battery Charging. Battery Discharging. Battery Fail
  • and Battery Reverse Polarity
  • High MTBF > 500k hrs. as per Telcordia SR-332
  • Overvoltage / Overcurrent / Over temperature / Short circuit protections.
Specification Sheet Make a Sales Enquiry

DRU-24V10ACZ- 24V 10A

Product Overview

Delta Electronics CliQII  DC-UPS Modules

The CliQ II Delta’s Chrome DC-UPS module is designed to use in small cabinets where space is very critical. The module requires less installation space due to its flat body with depth of only 55.6mm, 71mm wide and 91mm tall. The tough plastic case has flame retardant property certified to UL 94V-0 specification. The module supports 24Vdc system with external battery up to 12AH capacity and comes with potential free contacts for battery management signals and LED indicator for battery status. The highly efficient convection cooled design is certified to major safety approvals including IEC/EN/UL 60950-1 for ITE and UL 508 for Industrial, which allows the module to be used reliably in most industrial applications.

Specifications

OUTPUT
Output Voltage Range

23-28Vdc
Output Current

10.0A Max
Output Power

240W Max (24V, 10A)

Voltage Drop Between

Input and Output

Charging Mode

0.2V between DC input to load)

Voltage Drop Between

Input and Output

Buffering Mode

0.3V between battery to load @ 10A load
INPUT
Input Voltage Range 23 - 28Vdc

Input Current

Charging Mode: 0.5A ± 0.1A

Charging Time*

< 30hr ± 5hr for battery 24V/12AH
Efficiency

Charging mode: > 80.0%

Buffering mode: > 99.0%
Battery Input / Output Characteristics
Nominal Battery Voltage

24Vdc, SLA Sealed lead acid battery

2 x 12Vdc, SLA Sealed lead acid battery
Battery Voltage Range

33Vdc Max (the maximum voltage that will not cause damage to the unit)

20Vdc Min (the voltage level of battery to enable “BAT Fail” function)
Battery Capacity

3.3AH to 12AH
Battery Fuse

Auto 15A / 58V, MINI (Littelfuse) or similar in the battery path. The battery fuse protects the wires between the battery and the unit.
Battery Charging Mode

CC-CV mode (constant current-constant voltage) at 0.5A
End-of-Charge Voltage

The unit always charges with fix input voltage value
STANDARDS & APPROVALS
Electrical Equipment of Machines EN 60204-1

Electrical Equipment in

Power Installations

 EN 62477-1 / IEC 62103-1

Safety Entry Low Voltage

SELV (EN 60950-1)

PELV (EN 60204-1, EN 62477-1)
Electrical Safety UL 60950-1 and CSA C22.2 No. 60950-1 (File No. E191395), IEC 60950-1
Industrial Control Equipment UL 508 and CSA C22.2 No. 107.1-01 (File No. E315355)
CE In conformance with EMC Directive 2014/30/EU and Low Voltage Directive 2014/35/EU
Material and Parts RoHS Directive (2011/65/EU)
Galvanic Isolation Power Port to Signal Port: 1.0KVac
Emissions (CE & RE) CISPR 32, EN 55032, EN 55011, FCC Title 47: Class B

Component Power Supply

for General Use

 EN 61204-3
Immunity EN 55024, EN 61000-6-2
Electrostatic Discharge IEC 61000-4-2
Radiated Field IEC 61000-4-3
Electrical Fast Transient / Burst IEC 61000-4-4
Surge IEC 61000-4-5
Conducted IEC 61000-4-6

Power Frequency

Magnetic Fields

 IEC 61000-4-8
PROTECTIONS
Overvoltage Buffering Mode: 33Vdc Max will not cause damage to the unit, Latch Mode
Overload / Overcurrent Buffering Mode: < 18A, Latch Mode
Over Temperature Buffering Mode: < 90°C Surrounding Air Temperature inside the unit, Latch Mode
Short Circuit (at system) Buffering Mode: Shutdown, Latch Mode
Input Polarity Protection* Yes (DC OK = open contact, LED Status = Orange)
Battery Polarity Protection* Yes (DC OK = open contact, LED Status = Orange)
Wrong Battery Voltage Protection Shutdown, 35V Max (the maximum voltage that will not cause damage to the unit)
Deep Discharge Protection Yes (22V ± 1V)**
Degree of Protection IP20
Protection Against Shock Class III
Notes

*If the orange status LED is on, this indicates a failure in the installation. In this case, do not turn on power supply while the battery is connected. Danger of explosion!

** The unit will stop operating when the battery voltage detected is less than 22V ± 1V
Reliability Data MTBF

500,000 hrs. as per

Telcordia SR-332
ENVIRONMENTAL
Operating Temperature -20°C to +60°C (full power)
StorageTemperature 25°C to +85°C
Operating Humidity 5 to 95% RH (Non-Condensing)
Operating Altitude 0 to 3,000 Meters
Shock Test Operating IEC 60068-2-27, Half Sine Wave: 4G for a duration of 22ms, 3 time per direction, 9 times in total
Shock Test Non-Operating IEC 60068-2-27, Half Sine Wave: 50G for a duration of 11ms, 3 time per direction, 9 times in total
Vibration Operating IEC 60068-2-6, Sine Wave: 10Hz to 500Hz @ 19.6m/S² (2G peak); 10 min per cycle, 60 min for all X, Y, Z directions
Non-Operating IEC 60068-2-6, Random: 5Hz to 500Hz @ 2.09Grms); 20 min per axis for all X, Y, Z directions
Pollution Degree 2
MECHANICAL
Case Cover / Chassis Plastic
Dimensions (L x W x D) 91.0 x 71.0 x 55.6 mm
Unit Weight 0.14 kg
LED Indicator

Green LED: DC OK, Battery Charging (flash)

Red LED: Battery Fail

Orange LED: Reverse polarity, Battery Discharging (flash)
Cooling System Convection
Terminal

Input / Output / Battery: 6 Pins (Rated 300V/25A)

Signal: 6 Pins (Rated 300V/25A)
Wire

Input / Output / Battery: AWG 24-12

Signal: AWG 24-12
Mounting Rail

Standard TS35 DIN Rail in accordance

with EN 60715
Noise

Sound Pressure Level (SPL) < 40dBA

(1 Meter from power supply)

Technical Illustration

  • DRU - Buffering Time VS. Output Current DRU - Buffering Time VS. Output Current
  • DRU - Dimensions DRU - Dimensions
  • DRU - Device Description DRU - Device Description
Back to Top

Products

Customer Service


Product Partners

POWERBOX PACIFIC

Follow Powerbox Pacific

on Linkedin

POWERBOX PACIFIC LTD

Auckland Office:
+64 9 4158 320
sales@powerbox.co.nz

POWERBOX AUSTRALIA PTY LTD

Sydney (Head office):
+61 2 9457 2200
sales@powerbox.com.au
© 2024 Powerbox. All rights reserved.
Close

Ask Your Question